GizmoBench guides
Mulch Coverage Chart: Square Feet per Cubic Yard by Depth

One cubic yard of mulch covers roughly 160 square feet at 2 inches deep, 100 to 108 square feet at 3 inches, and 80 to 81 square feet at 4 inches. The small differences between published charts come from rounding, as the arithmetic below shows. The chart gives you the answer for a quick estimate, and the formula lets you handle any bed shape or depth. If you would rather skip the arithmetic, our mulch calculator takes a bed’s measurements and returns cubic yards, bags and coverage in your browser, with no account and no upload.
TL;DR
- One cubic yard is 27 cubic feet, so coverage in square feet is 27 divided by the depth in feet: about 324 sq ft at 1 inch, 162 at 2 inches, 108 at 3 inches and 81 at 4 inches.
- To find how much you need: area in square feet × depth in inches ÷ 12 gives cubic feet, and dividing by 27 gives cubic yards. The shortcut is square feet × depth in inches × 0.0031.
- Most beds call for 2 to 4 inches of mulch, depending on the material, and mulch should never be piled against a trunk or stem.
- A 2-cubic-foot bag is 1/13.5 of a yard, so one yard equals about 14 of those bags. Buying in bulk is the simpler order for large areas.
- Round up modestly, because a partial bag or yard cannot be delivered and a bed that comes out slightly thick is easier to fix than one that runs short.
Table of Contents
- The mulch coverage chart
- The formula behind the chart
- Worked examples
- Choosing a depth
- Trees and shrubs: keep mulch off the trunk
- From cubic yards to bags
- Ordering without running short
- Doing the calculation in the browser
- FAQ
- Sources
The mulch coverage chart
The table below states how far one cubic yard goes at each depth. The exact figures are straightforward arithmetic: a cubic yard holds 27 cubic feet, and a layer 1 inch (1/12 of a foot) thick spreads over 27 × 12 = 324 square feet. Published charts often round these. UC Marin Master Gardeners, for example, list 325 sq ft at 1 inch, 160 at 2 inches, 100 at 3 inches and 80 at 4 inches, so a chart that says 100 and one that says 108 for 3 inches are describing the same yard of mulch.
| Mulch depth | Coverage per cubic yard (exact) | Rounded chart figure | Cubic feet per 100 sq ft | Cubic yards per 100 sq ft |
|---|---|---|---|---|
| 1 inch | 324 sq ft | 325 sq ft | 8.3 | 0.31 |
| 2 inches | 162 sq ft | 160 sq ft | 16.7 | 0.62 |
| 3 inches | 108 sq ft | 100 sq ft | 25.0 | 0.93 |
| 4 inches | 81 sq ft | 80 sq ft | 33.3 | 1.23 |
| 6 inches | 54 sq ft | n/a | 50.0 | 1.85 |
The exact column and the last two columns are our own calculations from the 27-cubic-feet-per-yard definition. The rounded column comes from the UC Marin table. Use the exact column when you are ordering for a large area, because the gap between 100 and 108 square feet is 8 percent, which on a 1,000 square foot job is nearly a full yard.
How to read the chart
Find your depth in the first column, then divide your bed’s area by the coverage figure. A 400 square foot planting area at 3 inches needs 400 ÷ 108 = 3.7 cubic yards. If you only know the area, the last column works in the other direction: multiply the cubic yards per 100 sq ft by your area divided by 100.
The chart assumes the mulch is spread evenly over flat ground. Beds with mounds, dips or a lot of plants with wide crowns will take a little more or less, so treat the result as an estimate rather than a promise.
The formula behind the chart
Every chart on this topic comes from one calculation. Iowa State University Extension describes it in three steps: find the bed’s area in square feet, convert the depth from inches to feet, and multiply the two. Divide by 27 for cubic yards, or by the bag size in cubic feet for a bag count.
- Area. Multiply length by width for a rectangle. For a circle, multiply 3.14 by the radius squared. For an irregular bed, split it into rectangles and circles and add the pieces.
- Depth in feet. Divide the depth in inches by 12. Iowa State’s conversion table gives 2 inches as 0.166 feet, 3 inches as 0.25 feet and 4 inches as 0.333 feet.
- Volume. Area × depth in feet gives cubic feet. Divide by 27 for cubic yards.
Texas A&M’s Travis County horticulture program writes the same thing as one line: cubic yards = (length × width × (depth in inches ÷ 12)) ÷ 27. It also offers a shortcut, square feet × depth in inches × 0.0031. The shortcut works because 1 ÷ 12 ÷ 27 is 0.00309, which rounds to 0.0031.
Where the arithmetic goes wrong
Three slips account for most bad estimates. The first is using inches where feet belong, which inflates the answer by a factor of 12. The second is forgetting the division by 27, which leaves you with cubic feet while the supplier sells cubic yards. The third is measuring the bed’s outer edge and ignoring features inside it, such as a path or a stepping stone, which makes you overbuy. Our mulch calculator does the unit handling for you, so those three errors cannot happen, but it is worth knowing what it is doing so you can sanity-check the number it returns.

Worked examples
A rectangular bed: 12 ft by 8 ft at 3 inches
- Area: 12 × 8 = 96 sq ft
- Depth: 3 ÷ 12 = 0.25 ft
- Volume: 96 × 0.25 = 24 cubic feet
- In yards: 24 ÷ 27 = 0.89 cubic yards
- Shortcut check: 96 × 3 × 0.0031 = 0.89
- In 2-cubic-foot bags: 24 ÷ 2 = 12 bags
Because 0.89 yards is close to a full yard, many people order one yard in bulk for this bed and keep the leftover for later top-ups. That is a judgment call, not a rule: it depends on whether your supplier sets a minimum delivery and how you plan to store the pile.
A perennial bed from Iowa State’s guide
Iowa State Extension works through a 265 sq ft perennial bed mulched at 1.5 inches. That is 33.125 cubic feet, or 1.22 cubic yards in bulk, or about 17 bags of 2-cubic-foot mulch, with the bag count rounded up from 16.6. A 1.5 inch layer is thin by the standards of the 2 to 4 inch range, so this example suits a bed where the mulch is a light finishing layer over established plants.
A round ring: 3 ft radius at 3 inches
- Area: 3.14 × 3 × 3 = 28.3 sq ft
- Volume: 28.3 × 0.25 = 7.1 cubic feet
- In 2-cubic-foot bags: 3.5, so 4 bags
For a tree, the ring is only part of the story, because where the mulch goes matters as much as how much. The tree section below covers that.
A large area: 500 sq ft at 3 inches
Texas A&M’s example table puts a 500 sq ft area at 4½ yards at 3 inches. Our exact arithmetic gives 500 × 0.25 ÷ 27 = 4.63 yards. The two agree to within a fraction of a yard, and the table rounds to the nearest half yard. Either way, an order this size is a bulk delivery rather than a trip with a truck bed full of bags.
Choosing a depth
The depth you plug into the formula is the biggest lever on the order, since going from 2 inches to 4 inches doubles the volume. Extension guidance converges on a range. The Illinois Department of Natural Resources recommends 2 to 4 inches (5 to 10 cm): 2 to 3 inches for fine mulches such as compost, and 3 to 4 inches for coarse arborist wood chips. LSU AgCenter recommends 3 to 4 inches to help suppress weeds, and notes that natural mulch decomposes, so the layer should be refreshed every year or more often.
The Brooklyn Botanic Garden’s material chart gives different depths for different materials:
| Material | Recommended depth |
|---|---|
| Wood chips | 2 to 4 inches |
| Mixed bark | 2 to 3 inches |
| Compost | 3 inches |
| Leaves | 3 inches |
| Straw (chopped) | 1 to 2 inches |
| Pine needles | 1.5 inches |
| Grass clippings | 1 inch maximum |
| Cocoa hulls | 1 inch |
| Seaweed | 4 to 6 inches |
| Stone | 2 to 4 inches |
In practice, check the material first and then pick the depth from this list. A bed of shredded hardwood at 3 inches and a bed of pine needles at 1.5 inches need very different volumes, even if the bed is the same size.
Why more is not better
The Illinois DNR notes that on wet soils, more than 2 inches of organic mulch can lead to excess moisture around the roots and root rot, and that thick layers of fine mulch can mat and reduce water and air penetration. Brooklyn Botanic Garden’s advice is to mulch wide but not deep, because too much mulch cuts the oxygen available to roots. If your soil drains slowly, run the numbers at the lower end of the range.
Topping up an existing layer
If mulch is already down, measure its depth first. The Illinois DNR advises breaking up matted layers and refreshing them with a rake rather than adding more on top. Your order is then the difference between the depth you want and the depth you have. If you have 1 inch left and want 3, calculate for 2 inches: a 96 sq ft bed would need 96 × 2 × 0.0031 = 0.6 cubic yards, not the 0.89 a fresh bed would take.
Trees and shrubs: keep mulch off the trunk
The formula works the same way for a ring around a tree, but the placement rules are different. The Illinois DNR advises applying mulch near the trunk but not touching it, extending out to the drip line where practical, with a ring of at least 3 feet (1 meter) in radius for most trees. Brooklyn Botanic Garden recommends keeping mulch about six inches away from the trunk and never covering the root flare, where bark can rot if buried in moist material.

Piling mulch against the trunk is often called volcano mulching. The AP’s gardening coverage describes it as slowly suffocating trees, and the LSU AgCenter says it keeps bark moist and invites disease. When you measure a tree ring for the calculation, subtract the bare circle around the trunk. A 6 inch gap on a ring of 3 ft radius removes only about 0.8 sq ft of area, so the order barely changes, but the tree is much better off.
From cubic yards to bags
Bags are labeled in cubic feet, and the common sizes in the Texas A&M table are 0.75, 1, 1.25 and 2 cubic feet. One cubic yard equals:
| Bag size | Bags per cubic yard |
|---|---|
| 0.75 cu ft | 36 |
| 1 cu ft | 27 |
| 1.25 cu ft | 22 |
| 2 cu ft | 14 (13.5 rounded up) |
The same table shows that 3 cubic yards needs 41 bags of 2 cubic feet, which is 40.5 rounded up. Always divide your total cubic feet by the bag size on the actual label, then round up to a whole bag. Bag labels sometimes state a size that differs from the nominal figure, so read the one on the product you are buying.
To compare prices fairly between a bag and a bulk quote, convert both to the same unit. A bag priced per 2 cubic feet has to be multiplied by 13.5 to get a per-yard figure. Our unit rate calculator handles that comparison when the two prices are quoted in different units.
Bag or bulk
For small beds, bags are easier to carry, store and spread in stages. Past roughly one cubic yard (14 two-cubic-foot bags), most people find a bulk delivery simpler, since it replaces a car full of bags with a single drop. That threshold is a rule of thumb rather than a rule, and your own price quotes and access to the bed matter more.
Ordering without running short
Mulch is sold in whole bags and in yards that are often delivered in half-yard or full-yard increments, so the estimate usually needs rounding. We suggest three habits, which are our own practical assumptions rather than figures from a study:
- Round up to the next bag, or to the next half yard for bulk.
- Measure the bed in two ways if its outline is irregular, for example as a set of rectangles and then as a single rough oval, and trust the larger answer.
- Keep the rounded-up difference for the following season, since natural mulch breaks down and the Illinois DNR and LSU guidance both call for refreshing it rather than adding layers without checking.
For related materials in the same project, the formula is identical: area times depth, divided by 27. Our soil calculator covers raised beds, pots and fill, and the raised bed soil calculator works out bags for a framed bed. If you are also laying a path, the gravel calculator gives tons, yards and bags.
Doing the calculation in the browser
The chart is enough for a single rectangular bed, and the formula covers the rest. When you have several beds, a mix of bag sizes or a depth that differs from bed to bed, repeating the arithmetic invites mistakes. The mulch calculator takes the bed’s dimensions and depth and returns cubic yards, bags and coverage. Like our other tools, it runs in the browser without an account or an installation, so nothing you type is sent to a server. You can browse the rest of the everyday collection, including the unit converter and percentage calculator, on the everyday tools page.
FAQ
How much does one cubic yard of mulch cover?
About 162 square feet at 2 inches, 108 square feet at 3 inches and 81 square feet at 4 inches. Rounded charts such as the one from UC Marin Master Gardeners list 160, 100 and 80. The exact figure is 27 cubic feet divided by the depth in feet.
How do I work out how much mulch I need?
Multiply the bed’s area in square feet by the depth in inches, then by 0.0031, to get cubic yards. For a 96 square foot bed at 3 inches, that is 96 × 3 × 0.0031 = 0.89 cubic yards. To get bags instead, multiply area by depth in feet and divide by the bag size in cubic feet.
What depth of mulch is best?
Most guidance falls between 2 and 4 inches, with finer materials such as compost at the thinner end and coarse wood chips at the thicker end. On wet or slow-draining soil, the Illinois DNR cautions against going past 2 inches of organic mulch. Keep the layer clear of trunks and stems whatever depth you choose.
How many bags of mulch are in a yard?
About 14 bags of 2 cubic feet, 27 bags of 1 cubic foot, or 22 bags of 1.25 cubic feet. The exact figure for 2-cubic-foot bags is 13.5, so you round up to 14. Check the volume printed on the bag you are buying before you count.
Does the same chart work for soil or compost?
Yes, because the volume formula depends only on area and depth. A cubic yard of any loose material covers the same area at the same depth. The recommended depth differs by material, so choose it from the guidance for that product and then use the chart.
Sources
- Applying Mulch, UC Marin Master Gardeners
- How to Determine the Amount of Mulch Needed for a Garden Bed, Iowa State University Extension
- How Much Compost, Soil or Mulch?, Texas A&M Urban Programs Travis County
- Proper Mulching Techniques, Illinois Department of Natural Resources
- Make Landscape Bed Weed Management Easier for Yourself, LSU AgCenter
- How to Use Mulch, Brooklyn Botanic Garden
- Right ways and the wrong ways to use mulch in the garden, AP News