gizmobench
BrowseDaily

Half Step Down Guitar Tuner

Lower every string by one semitone from standard tuning. E♭ A♭ D♭ G♭ B♭ E♭ is also written D♯ G♯ C♯ F♯ A♯ D♯. This page opens on E♭2 A♭2 D♭3 G♭3 B♭3 E♭4, from the lowest string to the highest. Play a reference tone to tune by ear, or allow the microphone to see the nearest string and its pitch difference in cents. Pluck one string at a time and let it settle before reading.

Tune with your microphone

Your browser asks for permission first, because no page may listen without it. The samples are read in the page and dropped: nothing is recorded and nothing is uploaded.

Nothing is recordedNothing is uploadedThe stream closes when you stopNo account, nothing installed
Tuning
Reference

The cents bar follows the nearest open string in the selected tuning. Use Selected string to keep a fixed target.

The microphone is closed. Press Start to tune with it, or Play to hear a reference tone.

Why the browser asks permission first. A page cannot listen until you allow it, and the prompt is your browser's, not this site's. Allow it, play one string on its own, and the note should appear within a moment. The tuner reads the samples as they arrive and throws them away: there is no recording, and the stream closes the moment you press Listening or leave the page. Noise suppression and automatic gain are requested off, because a gate that mutes the room between notes, or a gain that rides a decaying string, gets between the detector and the string.

Strings in each tuning

Every listed frequency here is at A = 440, the reference chosen above, and sets the generated reference tone. Physical playback also depends on your device clock. Any string is tuned the same way: play it, watch the bar, and turn the peg until the needle sits in the green. Sharp means the measured pitch is higher than the target; flat means lower. Ukulele high G is re-entrant, so its first listed string is not the lowest pitch.

TuningStrings in instrument orderFrequencies
StandardE2 A2 D3 G3 B3 E482.4 Hz, 110.0 Hz, 146.8 Hz, 196.0 Hz, 246.9 Hz, 329.6 Hz
Drop DD2 A2 D3 G3 B3 E473.4 Hz, 110.0 Hz, 146.8 Hz, 196.0 Hz, 246.9 Hz, 329.6 Hz
Half step downEb2 Ab2 Db3 Gb3 Bb3 Eb477.8 Hz, 103.8 Hz, 138.6 Hz, 185.0 Hz, 233.1 Hz, 311.1 Hz
BassE1 A1 D2 G241.2 Hz, 55.0 Hz, 73.4 Hz, 98.0 Hz
Whole step downD2 G2 C3 F3 A3 D473.4 Hz, 98.0 Hz, 130.8 Hz, 174.6 Hz, 220.0 Hz, 293.7 Hz
Open DD2 A2 D3 F#3 A3 D473.4 Hz, 110.0 Hz, 146.8 Hz, 185.0 Hz, 220.0 Hz, 293.7 Hz
Open CC2 G2 C3 G3 C4 E465.4 Hz, 98.0 Hz, 130.8 Hz, 196.0 Hz, 261.6 Hz, 329.6 Hz
C standardC2 F2 Bb2 Eb3 G3 C465.4 Hz, 87.3 Hz, 116.5 Hz, 155.6 Hz, 196.0 Hz, 261.6 Hz
Baritone B standardB1 E2 A2 D3 F#3 B361.7 Hz, 82.4 Hz, 110.0 Hz, 146.8 Hz, 185.0 Hz, 246.9 Hz
Double drop DD2 A2 D3 G3 B3 D473.4 Hz, 110.0 Hz, 146.8 Hz, 196.0 Hz, 246.9 Hz, 293.7 Hz
Five-string bassB0 E1 A1 D2 G230.9 Hz, 41.2 Hz, 55.0 Hz, 73.4 Hz, 98.0 Hz
Six-string bassB0 E1 A1 D2 G2 C330.9 Hz, 41.2 Hz, 55.0 Hz, 73.4 Hz, 98.0 Hz, 130.8 Hz
Bass drop DD1 A1 D2 G236.7 Hz, 55.0 Hz, 73.4 Hz, 98.0 Hz
Bass drop CC1 G1 C2 F232.7 Hz, 49.0 Hz, 65.4 Hz, 87.3 Hz
Bass D standardD1 G1 C2 F236.7 Hz, 49.0 Hz, 65.4 Hz, 87.3 Hz
Ukulele high GG4 C4 E4 A4392.0 Hz, 261.6 Hz, 329.6 Hz, 440.0 Hz
Ukulele low GG3 C4 E4 A4196.0 Hz, 261.6 Hz, 329.6 Hz, 440.0 Hz
Baritone ukuleleD3 G3 B3 E4146.8 Hz, 196.0 Hz, 246.9 Hz, 329.6 Hz
Accuracy. Autocorrelation resolves synthetic steady tones above 80 Hz to within one cent. Microphone noise, harmonics and a decaying string can widen or shift readings. Reference tones use equal-tempered target frequencies; playback depends on the device clock. No audio is recorded or sent anywhere.

Common questions

What notes are used in half step down?
E♭2 A♭2 D♭3 G♭3 B♭3 E♭4, from the lowest string to the highest. Lower every string by one semitone from standard tuning. E♭ A♭ D♭ G♭ B♭ E♭ is also written D♯ G♯ C♯ F♯ A♯ D♯.
Can I tune without allowing the microphone?
Yes. Press each string’s reference tone and compare it with your instrument by ear. The microphone is only needed for automatic pitch detection.
Why does the tuner show a different note immediately after I pluck?
The initial attack and nearby strings can confuse pitch detection. Mute the other strings, pluck one cleanly and read after the sound settles. Move a tuning peg in small steps.
How do I keep the tuner on one string?
Choose Selected string and select the intended target. Its cents bar stays on that string even if the played pitch is nearer another string. Nearest chromatic note instead measures against the detected equal-tempered note. Both modes analyse one pitch at a time.

Autocorrelation resolves synthetic steady tones above 80 Hz to within one cent. Microphone noise, harmonics and a decaying string can widen or shift readings. Reference tones use equal-tempered target frequencies; playback depends on the device clock. No audio is recorded or sent anywhere.